當前位置：
依客思防爆科技有限公司 >
產品中心 >
防爆LED燈類 > 依客思防爆聲光報警器消防警報燈24v12v消防火災LED警示閃光燈三色燈BBJ
依客思防爆聲光報警器消防警報燈24v12v消防火災LED警示閃光燈三色燈BBJ
| 產品型號： |
BBJ |
| 品 牌： |
依客思 |
|
|
| 所 在 地： |
湖北武漢 |
| 更新日期： |
2026-07-20 |
| | 品牌：依客思 | | 類型：防爆應急燈 | | 加工定制：是 | |
| | 光源類型：LED | | 光源功率：3-10 W | | 電壓：2436220 V | |
| | 防護等級：IP65 | | 主要適用范圍：當生產現場發生事故或火災等緊急情況時，能由火災報警控制器啟 | | 型號：BBJ | |
防爆聲光報警器是一種結合了聲音和光線報警功能的安全裝置，專為含有爆炸性氣體環境場所設計。以下是對防爆聲光報警器的詳細介紹：
一、概述
防爆聲光報警器（簡稱報警器）為非編碼型報警器，適用于安裝在含有ⅡC（ⅡB）級T6溫度組別的爆炸性氣體環境場所。當生產現場發生事故或火災等緊急情況時，火災報警控制器送來的控制信號啟動聲光報警電路，發出聲和光報警信號，以完成報警目的。本產品也可同手動報警按鈕配合使用，達到簡單的聲、光報警目的。
二、技術參數
防爆標志：ExdⅡbT6
工作電壓：DC24V；AC220V（也有AC127V的選項）
報警電流：DC24V時≤600mA
頻閃頻率：60次/min
聲響強度：100-115dB
聲響形式：消防聲（可根據用戶需求設計成警笛聲、救護車聲）
防護等級：IP65或無防護
使用環境：溫度：-20℃-+50℃；相對濕度：≤95% 不結露；大氣壓力：80KPa-110KPa
進線口徑：M22×1.5（進線口徑的數量及大小可以根據用戶的需求設計生產）
重量：1.4Kg
三、產品特點
報警器外殼為全不銹鋼殼體或ZL102鋁合金壓鑄成型，表面高壓靜電噴塑，具有高強度和耐腐蝕性。
燈殼抗沖擊能力強，采用360°清晰可視超高亮LED發光管，配備超強蜂鳴器，確保在惡劣環境下穩定工作。
報警器具有工作穩定、使用壽命長、功耗低的特點，且不受污染物和水的影響。
四、安裝與布線
根據現場情況，使用M6膨脹螺釘或M6螺釘將火災聲光報警器的防爆外殼固定在墻壁上。
連接電纜外徑為φ6～8mm的橡塑電纜，電纜的防爆進線口為M22×1.5螺紋，可與鍍鋅護管或BNG15×700防爆撓管連接，也可以使用防爆封口螺帽鎖緊。
接線時，需按照防爆火災聲光報警器布線示意圖，將控制線分極性分別接在火災聲光報警器接線端子的+、—兩端。注意防爆面不要夾雜導線或其它異物。
布線要求：線間、線與大地間絕緣阻抗大于20MΩ，探測總線回路單根線路電阻小于20Ω。
五、適用范圍
防爆聲光報警器適用于石油、化工、礦山、隧道等易燃易爆場所，以及家庭、學校、商場等公共場所。一旦探測器檢測到異常情況，如火災、氣體泄漏等，能夠迅速響應，發出高分貝的警報聲和強烈的光閃，以引起人們的注意，并采取緊急措施。
總之，防爆聲光報警器以其獨特的防爆性能和高效、直觀的報警方式，成為守護每一刻的重要工具。
Explosion-proof sound and light alarm is a combination of sound and light alarm function of the safety device, specially designed for places containing explosive gas environment. The following is a detailed introduction to the explosion-proof sound and light alarm:
I. Overview
Explosion-proof sound and light alarm (referred to as alarm) is a non-coding alarm, suitable for installation in explosive gas environments containing ⅡC (ⅡB) class T6 temperature group. When an accident or fire and other emergency occurs on the production site, the control signal sent by the fire alarm controller starts the sound and light alarm circuit and sends out the sound and light alarm signal to complete the alarm purpose. This product can also be used with manual alarm buttons to achieve simple acoustic and optical alarm purposes.
2. Technical parameters
Explosion-proof mark: ExdⅡbT6
Working voltage: DC24V; AC220V (also available with AC127V option)
Alarm current: DC24V ≤600mA
Stroboscopic frequency: 60 times /min
Sound intensity: 100-115dB
Sound form: fire sound (can be designed as a police siren, ambulance sound according to user needs)
Protection level: IP65 or no protection
Operating environment: Temperature: -20℃-+50℃; Relative humidity: ≤95% no condensation; Atmospheric pressure: 80KPa-110KPa
Inlet diameter: M22×1.5 (The quantity and size of inlet diameter can be designed and produced according to the needs of users)
Weight: 1.4Kg
Third, product characteristics
The shell of the alarm is made of stainless steel shell or ZL102 aluminum alloy die-casting molding, the surface of high voltage electrostatic spray, with high strength and corrosion resistance.
The lamp shell has strong impact resistance, adopts 360° clear visual ultra-bright LED light tube, and is equipped with super buzzer to ensure stable operation in harsh environment.
The alarm has the characteristics of stable operation, long service life, low power consumption, and is not affected by pollutants and water.
Fourth, installation and wiring
Use M6 expansion screws or M6 screws to secure the explosion-proof shell of the fire sound and light alarm to the wall according to the site conditions.
Connect the rubber and plastic cable with an outer diameter of φ6 ~ 8mm, and the explosion-proof inlet of the cable is M22×1.5 thread, which can be connected with the galvanized protective pipe or BNG15×700 explosion-proof flexible pipe, and can also be locked by explosion-proof sealing nuts.
When connecting cables, connect the control cables to the + and - ends of the wiring terminals of the fire alarm according to the wiring diagram of the explosion-proof fire alarm. Pay attention to the explosion-proof surface do not include wire or other foreign matter.
Wiring requirements: The insulation impedance between wires and between wires and the ground is greater than 20MΩ, and the resistance of a single line of the probe bus loop is less than 20Ω.
V. Scope of application
Explosion-proof sound and light alarm is suitable for flammable and explosive places such as petroleum, chemical industry, mines, tunnels, as well as public places such as families, schools, shopping malls. Once the detector detects an abnormal situation, such as fire, gas leakage, etc., it can respond quickly, emit a high-decibel alarm and a strong light flash to attract people's attention and take emergency measures.
In short, explosion-proof sound and light alarm with its unique explosion-proof performance and efficient and intuitive alarm mode, become an important tool to guard every moment.
手機訪問
防爆聲光報警器是一種結合了聲音和光線報警功能的安全裝置，專為含有爆炸性氣體環境場所設計。以下是對防爆聲光報警器的詳細介紹：
